0
×

Your shopping cart is empty.

View Cart
  • Home
  • Marking Devices
  • Signage
  • Consecutive Numbering Machines
  • Industrial Inks
  • Embossers
  • Public Guidance Systems
  • Evidence Collection
  • Stamp Pads
  • Replacement Stamp Pads and Ink Cartridges
  • Stenciling
  • Electic Time Clocks / Perforator Machines
  • Ticket Punches
  • Electric Branding Products
  • Notary Public Supplies
  • Professional Seals and Stamps
  • Land Surveyor Stamps
  • (M)SDS Technical Data Sheets
  • Monograms and Personalized Stationery Products
  • Reiner Numbering Stamp Video
  • Shiny Heavy Duty Video
  • RibType Video
  • Paint Stripping New Rider 5000 Video
  • How To Change a Trodat Ink Cartridge
  • How To Change a Shiny Printy Pad
  • How To Change the Rubber Die
  • How To Re-Ink Large 3 Fingerprint Pad
  • About HITT Marking
  • Product Catalog
  • Download Catalog
  • In the News
  • Shipping Information
  • Contact
1oz INSTA MARK Re-Inking Fluid

1oz INSTA MARK 214 Re-Inking Fluid

SKU: IN-INSTA-MARK-INK
Your Price $15.00
Quantity
 
1oz Insta-Marks Re-Inking Stamp Ink

Re-inking fluid for all the Insta-Mark stamps

Colors available;
Black
Blue
Green
Purple
Red
White

Directions For Use:
Always use resealable bag for storage. Proper care of the Insta Mark 116 and 126 will
give you clean, consistent impressions each and every time. Make certain to follow these instructions carefully.

1. How Often Should the Insta Mark be re-inked?

The Insta Marks should be re-inked approximately every 2,000 marks. It is important not to run the stamp completely dry. By adding the appropriate number of drops (15-20) every 2,000 marks you will
be able to keep the stamp moist and in condition to handle high volume marking or long term storage.

2. Use ONLY Mark-Hitt 214 Ink. The chemical composition of your Insta Mark may be jeopardized with the use of any other ink. Swelling and distortion may occur.

3. Do not leave Insta Mark cap off for extended period of time. Do not use stamp pad.

4. Do not clean! The Insta Mark die will remain moist. Therefore, layers of dried ink will not accumulate. Cleaning is not necessary. Do not rub or allow the impression surface to come in contact with sharp objects. However, should the die face become dusty or dirty you may take a piece of clear scotch tape and gently place it on the stamp surface. Rub your finger three or four times across scotch tape. Then, gently remove tape from stamp face. Repeat if necessary.

5. Press gently. A hard strike is not necessary. By stamping softly a minimum amount of ink will be transferred and the drying time will be decreased. If the stamp is making a heavy ink mark, follow re-inking instruction step # 3 below. (Adjusting Pressure Insert)

6. Replace cap. Do not allow your Insta Mark to remain uncapped for over 3-5 minutes at one time. Fast dry inks evaporate quickly. If the rubber die begins to dry or the mark becomes light, recap tightly and put the Insta Mark aside for 15-30 minutes. If the ink does not regenerate, follow the re-inking instructions. (See Below) For clean impressions with excellent adhesion - do not stamp on wet or
greasy surfaces. We recommend wiping the surface clean with Re-activator.

After removing your Printed Circuit Board, or other material, from a degreasing bath - let the solvent evaporate before touching the mark (this should take about 2-3 seconds). The mark will then remain permanent.

Warning: Keep out of the reach of children. Avoid skin contact. If skin contact is made, wash the affected area with soap and water.


Any questions call 714-979-1405 or email us at
Sales@HittMarking.com
    Product Options and Custom Information
    Special Instructions:
    Ink Choices;

    Customer Reviews