All of our steel stamps are made with carbon tool steel. They're tough enough to keep on stamping long after other stamps lose their face. We use a special heat treatment so they won't shatter under stress. Each steel stamp is manufactured to our high standards right here in the U.S.A.


It is not unusual to overestimate the size of character needed. A character is measured from cutting edge to cutting edge. Impression size will vary with the depth of penetration: Diagram


Machine-made Machine-made

More marks per dollar with this economical, quality steel stamp. Sharp characters in Gothic style ensure deep, clear impressions. One thumb groove.
Letter Sets (27 PC. - 26 letters & ".")
Letter Set
Number: Height:
01271 1/16"
02271 3/32"
03271 1/8"
05271 3/16"
06271 1/4"
08271 3/8"
09271 1/2"
-
Figure Sets (9 PC.)
Figure Set
01091 1/16"
02091 3/32"
03091 1/8"
05091 3/16"
06091 1/4"
08091 3/8"
09091 1/2"
-
Combination Letter &
Figure Sets (36 PC.)
Combination Set
01361 1/16"
02361 3/32"
03361 1/8"
05361 3/16"
06361 1/4"
07361 5/16"
08361 3/8"
09361 1/2"


Hand-cut Hand-cut

Individually inspected character with special hand-ground taper to assure precision impression alignment. Character indentification and one thumb groove.
Letter Sets (27 PC. - 26 letters & ".")
Letter Set
Number: Height:
01272 1/16"
02272 3/32"
03272 1/8"
05272 3/16"
06272 1/4"
07272 5/16"
08272 3/8"
09272 1/2"
-
Figure Sets (9 PC.)
Figure Set
01092 1/16"
02092 3/32"
03092 1/8"
05092 3/16"
06092 1/4"
07092 5/16"
08092 3/8"
09092 1/2"
-
Combination Letter &
Figure Sets (36 PC.)
Combination Set
01362 1/16"
02362 3/32"
03362 1/8"
05362 3/16"
06362 1/4"
07362 5/16"
08362 3/8"
09362 1/2"


Heavy-duty Heavy-duty

Made to meet the demands of rigid service. Extra heavy, extra length shank with heavy supporting bevel. Character indentification and size, three thumb grooves.
Letter Sets (27 PC. - 26 letters & ".")
Letter Set
Number: Height:
00273 1/32"
01273 1/16"
02273 3/32"
03273 1/8"
04273 5/32"
05273 3/16"
06273 1/4"
07273 5/16"
08273 3/8"
09273 1/2"
10273 5/8"
-
Figure Sets (9 PC.)
Figure Set
00093 1/32"
01093 1/16"
02093 3/32"
03093 1/8"
04093 5/32"
05093 3/16"
06093 1/4"
07093 5/16"
08093 3/8"
09093 1/2"
10093 5/8"
-
Combination Letter &
Figure Sets (36 PC.)
Combination Set
00363 1/32"
01363 1/16"
02363 3/32"
03363 1/8"
04363 5/32"
05363 3/16"
06363 1/4"
07363 5/16"
08363 3/8"
09363 1/2"


Reversed Reversed

For use in marking plastic molds, rubber molds, thin metal patterns, forging dies, etc. Produces a reversed impression in the mold which makes a raised letter on the molded product. Character indentification and size, three thumb grooves.
Letter Sets (27 PC. - 26 letters & ".")
Letter Set
Number: Height:
00274 1/32"
01274 1/16"
02274 3/32"
03274 1/8"
04274 5/32"
05274 3/16"
06274 1/4"
07274 5/16"
08274 3/8"
09274 1/2"
-
Figure Sets (9 PC.)
Figure Set
00094 1/32"
01094 1/16"
02094 3/32"
03094 1/8"
04094 5/32"
05094 3/16"
06094 1/4"
07094 5/16"
08094 3/8"
09094 1/2"
-
Combination Letter &
Figure Sets (36 PC.)
Combination Set
00364 1/32"
01364 1/16"
02364 3/32"
03364 1/8"
04364 5/32"
05364 3/16"
06364 1/4"
07364 5/16"
08364 3/8"
09364 1/2"


Round face - Full character Round face - Full characters

The cutting edge of the character is 1/32" radius, with a 40 degree bevel. Rounded character stamp makes low-stress impressions suitable for use anywhere metal strength is critical. The aircraft, missile, oil supply and nuclear power industries depend on these stamps to avoid risk of fracture from too sharp an imprint. Character indentification and size, three thumb grooves.
Letter Sets (27 PC. - 26 letters & ".")
Letter Set
Number: Height:
03275 1/8"
05275 3/16"
06275 1/4"
07275 5/16"
08275 3/8"
09275 1/2"
-
Figure Sets (9 PC.)
Figure Set
03095 1/8"
  05095 3/16"
  06095 1/4"
  07095 5/16"
  08095 3/8"
  09095 1/2"
-
Combination Letter &
Figure Sets (36 PC.)
Combination Set
03365 1/8"
05365 3/16"
06365 1/4"
07365 5/16"
08365 3/8"
09365 1/2"


Round face - Dot design characters Round face - Dot design characters

The cutting edge of the character is 1/32" radius, with a 40 degree bevel. For use in aircraft, missile, oil supply and nuclear power industries and other applications where lowest stress impressions are critical. Round face - dot design eliminates risk of fracture from too sharp an impression. Character indentification and size, three thumb grooves.
Letter Sets (27 PC. - 26 letters & ".")
Letter Set
Number: Height:
03276 1/8"
05276 3/16"
06276 1/4"
07276 5/16"
08276 3/8"
09276 1/2"
-
Figure Sets (9 PC.)
Figure Set
03096 1/8"
05096 3/16"
06096 1/4"
07096 5/16"
08096 3/8"
09096 1/2"
-
Combination Letter &
Figure Sets (36 PC.)
Combination Set
03366 1/8"
05366 3/16"
06366 1/4"
07366 5/16"
08366 3/8"
09366 1/2"
Deluxe Bar Marker
  • Variable Speed
  • 2 HP Motor with Gear Reduction
  • Hex Stock Capacity 1/4" to 2 7/8"
  • Accepts 3" O.D. x .750 I.D. Bar Marking Dies
Junior Roll Marker
This machine is designed to meet your present and future Roll Marking requirements. Single hand control allows machine to mark in both directions to increase die life and speed of marking. 
Air cylinders are sized to your present requirements for saving shop air. If future requirements require additional power cylinders can be added without alterations to base machine.
Power: Air or Hydraulic
Stroke: to 5"
Max. Diameter: to 9 1/2" - Designed for marking 1, 2 or 3 lines in steel, brass, aluminum, etc.
Height: 23"
Width: 14"
Weight: 200lbs. ( approx. shipping )
Applications: Impression marking round, solid, tubular or mill finished materials. Head marking of special fasteners and aircraft parts.
Carton Marker
Easy to Operate
Ideal for Cell Marking
Quick Change Tool Feature
Minimal Maintenance Required
4" Diameter Air Cylinder
1" Stroke
Requires min. 60 psi Air Pressure
Hydraulic Roll Markers
This machine is designed to meet your present and future Roll Marking requirements. Single hand control allows machine to mark in both directions to increase die life and speed of marking. 
Air cylinders are sized to your present requirements for saving shop air. If future requirements require additional power cylinders can be added without alterations to base machine.
Power: Air or Hydraulic
Stroke: to 5"
Max. Diameter: to 9 1/2" - Designed for marking 1, 2 or 3 lines in steel, brass, aluminum, etc.
Height: 23"
Width: 14"
Weight: 200lbs. ( approx. shipping )
Applications: Impression marking round, solid, tubular or mill finished materials. Head marking of special fasteners and aircraft parts.
Numbering Heads

Ideal when stamping Date and Part No.'s requiring frequent changes. 
Special wheels can be engraved with any combination of figures & letters. Sharp Face for Metal and Flat Face for Hot Stamping.
These units are available in all sizes.
TYPE HOLDERS

Quick-change and lite-duty type holders are constructed from select shock tool steel and designed to give you years of precision marking. 
These holders feature a quick-release button for easy loading or removal of type.
Each holder will accommodate Mercury Steel Type characters 1/32-inch thru' 5/16-inch high.
Available with a shepherd hook locking pin for easy loading or a machined retainer for permanent locking of steel marking type. 
Standard openings from 5/8-inch to 2-1/2 inch single and double line capacity.
Special type holders for specific tooling and marking problems are also available.
 
Home • Company Profile • Products • Contact Us • Index • Search